Zapi AC-2 Wartungshandbuch PDF herunterladen (Seite 102)

102

- 15/18/20BT-7, 16/18/20B-7 Traction Master (03) setup.

PARAMETER CHANGE

DESCRIPTION

(Service

level)

E mode N mode H mode

ACCELER. DELAY

LEVEL = 7 LEVEL = 6 LEVEL = 2

1 1

RELEASE BRAKING

LEVEL = 2 LEVEL = 3 LEVEL = 4

1 2

INVERS. BRAKING

LEVEL = 1 LEVEL = 3 LEVEL = 4

1 3

PEDAL BRAKING

1 6

SPEED LIMIT BRK.

2 8

BRAKE CUTBACK

3 0

MAX SPEED FORW

96 112 131

3 1

MAX SPEED BACK

96 112 131

2 1

CUTBACK SPEED 1

2 5 3

TURTLE SPEED

2 9

CURVE CUTBACK

2 4 5

FREQUENCY CREEP

6 3

MAXIMUM CURRENT

2 4 1

ACC. SMOOTH

2.5 2.0 1.0

2 4 2

INV. SMOOTH

2.5 2.0 1.0

2 4 3

STOP SMOOTH

15 10 10

2 4 8

SEAT DELAY TIME

2 4 2

SEQUENCE DE.TIME

2 4 8

CHAT TIME

60%

70Hz

30%

0.30

LEVEL = 8

LEVEL = 4

LEVEL = 5

2.0

After the CHAT TIME has passed and no travel/pump request has been activated the main contactor is

opened. Encoder signal is also monitored, To resume a travel/pump request is needed.

Different form to the acceleration curve after a direction inversion in

the frequency range 0 Hz to “Stop smooth” value (see also Dual ac2 manual).

To sets the level of frequency where the smooth effect on the acceleration ramp ends.

It determines the traction deactivation delay when the seat switch is opened.

Max. Delay time between the accelerator is pressed and a direction is selected (SRO)

% Percentage of max speed applied when the steer is fully turned right/left. No speed reduction is applied

when the steer angle is within the range [-8°;8°]. A linear reduction is applied in the middle.

Min. speed when the forward or reverse switch is closed, with accelerator in its min. position.

This changes the maximum current of the inverter.

Difference form the acceleration curve in the frequency range 0 Hz to “Stop smooth” value (see Dual ac2

manual).

To set maximum speed in forward direction.

To set maximum speed in backward direction.

% of max speed applied when the cutback switch is active. When set on 100% speed reduction is 0

% of max speed applied when "turtle" speed is active. When set to 100% the speed reduction is 0

Code

Parameter explanation.

Brake force when the accelerator pedal position is changed but not completely released.

Deceleration ramp when the speed reduce input becomes active and the motor slow down.

48V (Europe)

LEVEL = 9

Determines the traction acceleration ramp-up. It's adjustable between 0 and 100Hz.

Deceleration ramp when accelerator pedal is released. Adjustable form 0 to 100Hz.

Brake force when direction switch is inverted during travel. Adjustable from 0 to 100 Hz

Brake force when travel request is released and brake pedal switch is closed. Adjustable from 100 to 0 Hz

(Electrical brake support when mechanical brake is applied.

1 2 ... 97 98 99 100 101 102 103 104 105 106 107 ... 145 146

Kommentare zu diesen Handbüchern

Keine Kommentare

Zapi AC-2 Wartungshandbuch Seite 102

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Netzteile und Wechselrichter Zapi AC-2